Office Pickup Available Sat–Thu, 10 AM–8 PM • Order online before visiting • Use coupon easy5 for 5% off eligible orders.
Cart৳ 0 0

XH2.54mm Right Angle male Connector 2 to 10 Pin | 90° Bent Pin JST XH Header

Price range: ৳ 6 through ৳ 26

Quantity Pricing
QuantityDiscountUnit price
1–19StandardSelect an option
20–5010% off—
51+20% off—
Current unit price: Select a variation
✓ Checked componentsQuality-focused sourcing ৳ bKash acceptedMerchant: 01406080260 COD availableSubject to delivery area Technical helpAsk before you order
SKU: 56418-10 Category:

Description

A low-profile plug-in link that lies flat on your board.

The XH2.54mm right angle connector is a white header with 90 degree bent pins. The plug goes in sideways, parallel to the board, so cables run flat along the PCB. This suits slim cases and tight layouts. It is available from 2 pin to 10 pin for batteries, sensors, fans, LEDs and motors.

  • 2.54 mm pitch
  • 90° bent pin
  • 2 to 10 pin

side viewXH 2.54 mm · 90° Bent

XH2.54mm রাইট অ্যাঙ্গেল কানেক্টর হলো ২.৫৪ মিমি পিচের একটি সাদা হেডার, যার পিনগুলো ৯০ ডিগ্রি বাঁকানো। এতে প্লাগ পাশ থেকে ঢোকে, তাই তার বোর্ডের সাথে সমান্তরালে থাকে। ফলে স্লিম কেস বা ছোট জায়গায় ব্যবহার করা সহজ। ২ পিন থেকে ১০ পিন পর্যন্ত পাওয়া যায়। ব্যাটারি, সেন্সর, ফ্যান, LED ও মোটরের জন্য উপযোগী। এটি শুধু হেডার। তার ও মেটিং হাউজিং আলাদা কিনতে হবে।

Which pin count do you need?

Pick your use to see a good starting size. This listing comes in 2 pin, 3 pin, 4 pin, 5 pin, 6 pin, 7 pin, 8 pin, 9 pin and 10 pin.

2 pinPlus and minusBest for a battery, DC supply, LED strip, buzzer, small fan or motor.
3 to 7 pinOne pin more than the cell countA 2S pack uses 3 pins, 3S uses 4 pins, 4S uses 5 pins and 6S uses 7 pins. Check your charger or pack wiring first.
4 pinPower, ground and two signalsA common choice for I2C sensors, OLED displays and serial modules.
6 to 10 pinOne neat plug for a whole cableGood for button panels, display cables, encoders and multi-sensor boards.

General guide. Always confirm the pin order for your own project.

Specifications

2.54 mmpin pitch
2–10pin options
3 Atypical rated current
250 Vtypical rated voltage
90°bent pin type
ProductXH2.54mm connector header, right angle (bent pin)
Pitch2.54 mm (0.1 inch)
Pin type90 degree bent, through-hole soldering
Plug directionSideways, parallel to the PCB
Pin count options2 pin, 3 pin, 4 pin, 5 pin, 6 pin, 7 pin, 8 pin, 9 pin, 10 pin
Housing colourWhite
PolarizationKeyed, so the plug only goes in one way
Typical rating3 A, 250 V per pin for the XH series
Mates withXH2.54 wire housing and crimp terminals (sold separately)
CompatibilityJST XH style, 2.54 mm pitch
MountingPCB or perfboard, solder from the back
In the box1 × XH2.54mm right angle connector in your chosen pin count

What you can build

One small part, many neat connections.

Slim enclosures

Keep cables flat so the lid closes without bending wires.

Board-edge ports

Put the plug at the edge of a PCB for easy access.

Battery and balance leads

Add a clean side-entry plug for LiPo packs.

Sensor boards

Connect I2C and analog sensors with a short cable.

Robots

Plug motors and encoders into a low-profile controller.

Repair and replacement

Replace a broken right-angle XH header on a module.

Fit it in five steps

  1. Check the size. Count the pins you need and confirm a 2.54 mm pitch on your board or housing.
  2. Place the header. Push the bent pins through the holes with the plug opening facing the board edge.
  3. Solder. Solder each pin from the back and trim any extra length. Keep the housing flat against the board.
  4. Prepare the cable. Crimp XH terminals onto your wires and push them into the matching XH housing, red wire on the positive pin.
  5. Plug in. Slide the housing in sideways until it seats firmly.

Before you use it: this listing is the header only. The wire housing and crimp terminals are separate. Always check the pin order before connecting a battery, because a reversed plug can damage your parts. Ratings are typical for the XH series, so for high current or voltage check your wire gauge and your design.

Questions buyers ask

What does 90 degree bent pin mean?

The pins are bent at a right angle, so the plug enters from the side and the cable lies flat along the board.

How is it different from the straight pin version?

The straight type takes the plug from above. The right angle type takes it from the side, which saves height in slim cases.

Is this the same as a JST XH connector?

It is the same XH style with 2.54 mm pitch, so it mates with standard XH wire housings and terminals.

Does it come with the wire plug?

No. You get the right angle header only. Buy the XH housing and crimp terminals separately.

Which pin counts are available?

From 2 pin up to 10 pin. Choose the pin count from the options on this page.

Can I use it for a LiPo balance connection?

Yes, many balance leads use XH. A 2S pack uses 3 pins, 3S uses 4 pins and so on. Always match the pin order to your charger.

Do you deliver outside Dhaka?

Yes, we deliver all over Bangladesh.

Related searches

English: XH2.54 right angle connector price in Bangladesh, XH 2.54mm 90 degree bent pin BD, JST XH right angle header Dhaka, XH2.54 2 pin 3 pin 4 pin bent, LiPo balance connector Bangladesh, XH header male right angle, wire to board connector BD, Arduino shop Bangladesh, robotics shop Bangladesh

Banglish: XH2.54 bent pin connector dam koto, XH right angle connector kothay pabo, XH 2.54 90 degree price BD, JST XH kinbo kothay, electronics shop Dhaka

বাংলা: XH2.54 রাইট অ্যাঙ্গেল কানেক্টর দাম, XH 2.54 মিমি বাঁকানো পিন, JST XH কানেক্টর বাংলাদেশ, ব্যাটারি কানেক্টর, ইলেকট্রনিক্স শপ ঢাকা

Additional information

Pin Number

2Pin, 3Pin, 4Pin, 5Pin, 6Pin, 7Pin, 8Pin, 9Pin, 10Pin

⚙Project Support

Not sure whether this part is right for your project? Our team can help with component selection and integration.

3D3D Print & Fabrication

Need an enclosure, mount or prototype part? Ask about 3D printing and laser cutting/engraving.

LABLab Use Facility

Selected testing, prototyping and lab-use support is available for project teams and students.

Request project support →Open WhatsApp: 01309078343

Frequently Bought Together

🛠️ Change