Office Pickup Available Sat–Thu, 10 AM–8 PM • Order online before visiting • Use coupon easy5 for 5% off eligible orders.
Cart৳ 0 0

ISD1820 Voice Recording and Playback Module with Microphone and 0.5W Speaker

৳ 220

In stock

✓ Checked componentsQuality-focused sourcing ৳ bKash acceptedMerchant: 01406080260 COD availableSubject to delivery area Technical helpAsk before you order
SKU: 89329 Category:

Description

Record your voice. Play it back with one button.

The ISD1820 voice module records and plays back a short message of up to about 10 seconds. It has an onboard microphone, three push buttons and a 0.5W speaker, so it works the moment you power it. The message stays saved even when power is off. You can use it on its own or trigger it from an Arduino or any microcontroller.

  • 10 s record
  • Mic + 0.5W speaker
  • No code needed

ISD1820ISD1820 Module

ISD1820 ভয়েস মডিউল দিয়ে প্রায় ১০ সেকেন্ড পর্যন্ত নিজের কণ্ঠস্বর রেকর্ড করা এবং বাটন চাপলেই প্লে করা যায়। বোর্ডে মাইক্রোফোন, তিনটি বাটন এবং ০.৫ ওয়াটের স্পিকার আছে, তাই পাওয়ার দিলেই ব্যবহার করা যায়। রেকর্ড করা মেসেজ পাওয়ার বন্ধ করলেও মুছে যায় না। আলাদা কোড ছাড়াই চলে, আবার চাইলে Arduino দিয়েও কন্ট্রোল করা যায়। ডোর অ্যালার্ট, টয়, গিফট কার্ড ও ভয়েস প্রজেক্টের জন্য খুবই উপযোগী।

What will you use it for?

Pick a use to see how this module fits it.

PressRecord, then playHold the REC button and speak. Press PLAYE to hear it. No computer or code needed.
TriggerPlay a spoken warningWire a sensor or switch to the play pin so the module speaks when something happens.
TalkAdd a voice to anythingRecord a greeting for a toy, a card or a model and play it with a button.
2 pinsControl it from codeUse one pin for REC and one for PLAYE to record and play from your sketch.

General guide. Check the pin labels printed on your own module.

Specifications

10 srecord time
0.5 Wspeaker included
3–5 Vtypical supply
Savedkeeps memory when off
Miconboard microphone
ProductISD1820 voice recording and playback module
ChipISD1820 single-chip voice recorder
Recording lengthAbout 10 seconds per message (typical for this module)
MemoryNon-volatile, so the message stays after power off
Supply voltage3 V to 5 V (typical)
Speaker0.5 W, 8 ohm, with connector wire
MicrophoneOnboard electret microphone
ControlsREC, PLAYE and PLAYL push buttons
Control pinsVCC, GND, REC, PLAYE, PLAYL, FT, RP (check the silkscreen on your board)
Playback modesEdge trigger (PLAYE), level trigger (PLAYL) and repeat (RP jumper)
In the box1 × ISD1820 module and 1 × 0.5W speaker with wire, as shown

What you can build

Give your project a voice.

Talking door alert

Play a welcome or warning message when a sensor is triggered.

Greeting cards

Record a personal message for a gift.

Talking toys

Make a toy, doll or robot say your own line.

Voice reminders

Play a spoken reminder at the push of a button.

School projects

Add sound to models and science exhibits.

Arduino sound effects

Trigger short messages from your code.

Use it in four steps

  1. Connect the speaker. Plug the speaker wire into the speaker connector on the board.
  2. Power it. Connect VCC and GND to a 3 V to 5 V supply.
  3. Record. Press and hold the REC button, speak close to the microphone, then release. The LED lights while recording.
  4. Play. Press PLAYE to play the message once, or hold PLAYL to play while pressed.
// Arduino: record 5 seconds, then play it back
const int REC = 7;
const int PLAYE = 8;

void setup() {
  pinMode(REC, OUTPUT);
  pinMode(PLAYE, OUTPUT);
  digitalWrite(REC, LOW);
  digitalWrite(PLAYE, LOW);
}

void loop() {
  digitalWrite(REC, HIGH);    // start recording
  delay(5000);
  digitalWrite(REC, LOW);     // stop recording
  delay(500);
  digitalWrite(PLAYE, HIGH);  // trigger playback
  delay(100);
  digitalWrite(PLAYE, LOW);
  delay(8000);
}

Before you use it: a new recording replaces the old one, because the module holds one message. Keep messages under about 10 seconds. The speaker is small, so sound is clear but not very loud. Do not connect a larger speaker directly to the module. Always check the pin labels on your own board before wiring.

Questions buyers ask

How long can it record?

About 10 seconds. The module holds one message at a time.

Will the message be lost when I turn it off?

No. The memory is non-volatile, so your recording stays saved without power.

Do I need Arduino or coding?

No. The buttons on the board let you record and play with no code. You can use Arduino when you want automatic control.

Is the speaker included?

Yes. A 0.5W speaker with a connector wire comes with the module.

What is the difference between PLAYE and PLAYL?

PLAYE plays the whole message once with a short press. PLAYL plays only while you hold it.

Can I record music?

It is made for short voice messages. Sound quality is basic, so it is not meant for music.

Do you deliver outside Dhaka?

Yes, we deliver all over Bangladesh.

Related searches

English: ISD1820 voice module price in Bangladesh, ISD1820 recording module BD, voice record and playback module Dhaka, ISD1820 Arduino, voice recorder module with speaker, talking module for project, Arduino shop Bangladesh, electronics shop Bangladesh

Banglish: ISD1820 module dam koto, ISD1820 kothay pabo, voice record module price BD, voice module kinbo kothay, electronics shop Dhaka

বাংলা: ISD1820 ভয়েস মডিউল দাম, ভয়েস রেকর্ডিং মডিউল বাংলাদেশ, ISD1820 রেকর্ড ও প্লেব্যাক মডিউল, আরডুইনো ভয়েস মডিউল, ইলেকট্রনিক্স শপ ঢাকা

⚙Project Support

Not sure whether this part is right for your project? Our team can help with component selection and integration.

3D3D Print & Fabrication

Need an enclosure, mount or prototype part? Ask about 3D printing and laser cutting/engraving.

LABLab Use Facility

Selected testing, prototyping and lab-use support is available for project teams and students.

Request project support →Open WhatsApp: 01309078343
🛠️ Change